Electrical and Electronics

In the field of simulation work, it could proceed to an extent that, simulate with arbitrary values of the passive component and the voltage sources. The simulation results recorded various strategic points in the circuit indicate and validate the fact that the circuit is working in the expected lines with regard to the energy transfer in the expected lines with regard to the energy transfer in the tank circuit and sustenance in DC transient Analysis. Also in this proposed experimental work, it is observed that for an arbitrary load, the voltage obtained is agreeing with the theoretically computed DC-Voltage levels. The scope of the work can be extended to the actual calculation of the passives, the initial voltages across the capacitors and inductors. In addition to the exciting DC levels of the sources employed. The small signal analysis can also be done with due regard to the desired behavioural properties of switching devices used.

Transmission line protection is an important issue in power system engineering because 85 to 87% of power system faults are occurring in transmission lines. This paper presents a novel technique to detect and classify the different operating conditions in high voltage transmission lines to contribute quick and reliable operation of protection schemes. Discrimination among different operating conditions of transmission lines is achieved by combining wavelet transforms with support vector machine. MATLAB(7.3) / Simulink is used to simulate different operating conditions in high voltage transmission lines. The fault conditions considered are single phase to ground fault, line to line fault, double line to ground fault and three phase short circuit conditions. The circuit breaker operation and capacitor switching are the non-fault operating conditions. The discrete wavelet transforsms (DWT) are applied for analysis of simulated three phase current signals, because of its ability to extract information from the transient signal, simultaneously both in time and frequency domain. The wavelet family chosen is Daubechies, filter used – DB2, resolution level -3.The data sets which are obtained from the DWT are used for training and testing the support vector machine (SVM). In this proposed scheme SVM is used as classifier. It has the ability to detect and classify the given operating condition whether it is a fault or non-fault operating condition. It is concluded that this scheme discriminates the six different operating conditions considered in a very clear manner.

Nowadays, phasor measurement units are used in power networks for different purposes, such as Linearization of state estimation equations and speed improvement of controlling and protecting systems. Optimization of position and number of these equipments is considerably important because of their high costs. Effective parameters on position and number of PMUs optimization are: Network topology and zero injection buses in power networks. In this paper an objective function based on integer linear programming (ILP) is presented to determine the number and optimized position of PMUs, in order to complete observability of power systems. The effect of zero injection buses on objective function in power networks is evaluated. Simulation results are implemented in MATLAB software on the IEEE 14 buses system, and also 230kv and 400kv networks in Khouzestan province.

The four quadrant analog multiplier proposed by Rathor and Bhattacharya is reanalysed and modified in a different way for simple and low cost multiplication applications without using any reference waveforms. Verification of the feasibility of the circuit configuration is established by way of test results.

Improving distribution systems performance has become a significant issue as a result of large increase in electrical power consumption during recent years. The system operators aim to enhance efficiency of the distribution system in both dynamic and static modes. While DFACTS has commonly been employed to promote distribution systems capability in dynamic mode, this paper proposes a new static technique based on using interline dynamic voltage restorer (IDVR) to make a virtual smooth load duration curve for the adjacent loads having different load curves. Such a technique can be used for peak shaving and help the operator postpones the system expansion necessity. Furthermore, as a result of virtual smoothing load duration curve, voltage security margin and system reliability which are two important topics in static performance of the distribution systems will be enhanced. The simulation results demonstrate the suitability of the proposed technique.

Modern semiconductor switching devices are being utilized more and more in a wide range of applications These power electronics devices offer economical and reliable solutions to better manage and control the use of electric energy. However, the characteristics of most power electronics circuits, those semiconductor devices present nonlinear operational characteristics, which introduce contamination to voltage and current waveforms at the point of common coupling (PCC) of industrial loads. These devices, aggregated in thousands, have become the main polluters, the main distorters, of the modern power systems. At the Same time rapid development of semiconductor devices in power and control circuits, a new generation of equipments that help maintaining a good level of power quality, namely active power filters, has been developed. Theirs advantages over conventional means are more flexibility and very fast control response. The paper aim is to present the actual Power Quality Problems and solutions by active filters based on state-of-the-art power electronics technology and also their future prospects and directions.

Nowadays Hospital requirements are needed to be automated. During surgery, manual handling of surgical instruments may lead to human error. Here an automated surgical instrument lifting system is proposed and its movement carried over in four directions. System responds to voice and sensor signal from android accelerometer for controlling the motors connected with Microcontroller. Lifting of surgical instrument is done by a movable round table that rotates in a circular motion then a robotic arm lifts the surgical instruments using MATLAB software and Microcontroller hardware. Doctor’s voice command also used for executing the system.

Various phenomena occur in Air dielectric when a voltage is applied. When low voltage is applied, small current flows between the electrodes and the insulation retains its electrical properties. If the applied voltage is large, the current flowing through the insulation increases very sharply and an electrical breakdown occur. A strongly conducting spark formed during breakdown, practically produces a short circuit between the electrodes. The maximum voltage applied to the insulation at the moment of breakdown is called the breakdown voltage. For a uniform gap, the effect of humidity on the breakdown voltage is negligible. For non-uniform gaps such as rod-sphere, point-sphere like gaps the influence of humidity is found to be of significant. A correction procedure recommended by IEC is commonly used for converting the measured voltage or the test voltage from non-standard to standard reference atmosphere. So the result in analysis is then corrected into the standard reference conditions [in STP].

With the rapidly growing interest in smart grid technology, plug-in electric vehicles (PEVs) are expected to become more popular as low emission replacement for the petroleum based vehicles. Significant PEVs charging activities will mostly take place in customer’s premises, public or corporate car parks and electric charging stations. Therefore, utilities are concern about the possible detrimental impacts of these sizeable and unpredictable loads on the performance of distribution grids. Based on a recently proposed real-time smart load management (RT-SLM) control strategy, this paper focuses on the impact of uncoordinated and coordinated PEVs charging on substation transformer loading, system losses and voltage profile. Detailed simulations are performed on a 449 node smart grid system consisting of the modified IEEE 23 kV distribution system serving 4 charging stations and 22 low voltage residential networks populated with PEVs.

The paper presents an optimal fuzzy logic controller – controlled shunt active power filter (SAPF) used to compensate for harmonic distortion in three-phase systems. A optimal fuzzy logic controller based current controller strategy is used to regulate the filter current and hence ensure harmonic free supply current. The optimal adjustment of the membership functions and normalization gains are realized by using Ant Colony Optimization. Simulations results show the best dynamic behavior and performance control compared with traditional Fuzzy controller. as well as effective in reducing harmonic. The validity of the presented approach in harmonic mitigation is verified via simulation results of the proposed test system under different loading conditions.